Every vinyl fence we build comes with the same core scope: layout, post setting, panels, gates, and cleanup. Here is what is covered, and what we will flag before we start if your lot needs something different.
We mark the fence line with stakes and a string line, confirm property boundaries, and contact Colorado 811 for utility locates before any digging starts. Vinyl panels are fixed lengths, so the layout has to be exact before posts go in.
Vinyl posts go deep in concrete — frost depth in the Denver metro is commonly cited at about 36 inches — because a vinyl fence is only as straight as its posts. A heaved post shows immediately on a rigid panel run.
Vinyl panels are set on rails with metal reinforcement where the span and wind load call for it. We check the manufacturer's wind rating for the panel before quoting a long exposed run.
Vinyl gates get metal-reinforced frames and heavy hinges. A vinyl gate that sags is hard to fix after the fact, so the gate posts are set deeper than the line posts.
We check the Denver rules for your address — 4 feet in front of the primary facade, 6 feet behind it, zoning permit over 4 feet — and help with HOA submittals. Some HOAs and historic districts restrict vinyl, so we check before you commit to the material.
The old vinyl fence, concrete footings, and scrap all go in the trailer. We rake the work area, sweep the driveway, and walk the line with you before we go.
Vinyl fence installation Denver CO is the process of setting vinyl posts in concrete, hanging reinforced rails, and locking vinyl panels into place to create a privacy screen or decorative run. Panels come in fixed lengths, so the job is mostly layout: the line has to be measured to the panel, the posts have to be plumb and evenly spaced, and the gates have to be built to the opening, not the other way around.
Most Denver homeowners choose vinyl for one reason: no staining, no sealing, no rot. The material is PVC, so it does not absorb water at the ground line the way wood does. The honest limits are hail — a big stone can crack a panel — and heat and cold, which make vinyl expand and contract more than wood, so rails need room to move.
Every job follows the same four steps, whether it is a 40-foot side yard in Baker or a 300-foot perimeter in University Hills. You will know what happens each day.
Call
Call (720) 697-2456, Monday through Sunday, 7:00 AM to 8:00 PM. We will talk through the vinyl fence, the yard, and the lot, and set a time to measure.
Measure & plan
We measure the line to the panel length, check the ground and the slope, note trees and roots, and confirm the height, permit, and HOA rules for your address — including whether vinyl is allowed where you live.
Build
Posts go in concrete and cure, rails and panels go up plumb and level, and gates are reinforced, hung, and tested. We keep the site tidy as we go.
Walk-through
Before we leave, we walk the finished vinyl fence with you, check every gate and latch, and clear the site.
Post hole digger and auger
Used to bore clean 8- to 12-inch holes deep enough to clear the frost line. Vinyl posts are hollow, so the concrete footing does the structural work — the hole has to be right.
String line and level
The string line keeps the fence straight over 100 feet, and the level keeps every post plumb. Vinyl panels show a crooked post immediately, so we check both at every post.
Circular saw and fine-tooth blade
Vinyl cuts cleanly only with the right blade and a slow feed. A rough cut chips the panel edge and shows for the life of the fence.
Tamper and wheelbarrow
We tamp the soil around each footing so the vinyl fence post does not shift, and the wheelbarrow moves concrete mix to the hole.
Level and square for gates
Vinyl gates are built square on the bench and hung on reinforced posts. We check the diagonal before the gate goes on the hinges, not after.
Metal reinforcement inserts
Steel or aluminum inserts go inside rails and gate frames where the span or wind load calls for it, so the panel holds its shape through chinook gusts.
Posts set below Denver frost depth
The Denver metro frost depth is commonly cited at about 36 inches, and the exact code figure for fence posts is not settled in the sources we reviewed. We treat 36 inches as the floor, never the target, and set vinyl fence posts in concrete.
Room for expansion and contraction
Vinyl moves with temperature more than wood does. Rails are set with room to expand and contract so panels do not buckle in a July heat wave or pull apart in January.
Reinforced rails on long runs
A solid vinyl privacy run catches the full wind load. Reinforced rails and closer post spacing keep long runs from bowing or rattling in a chinook.
Hail-aware panel choice
Vinyl is the most hail-vulnerable fence material in Denver, and the 8 May 2017 storm caused $2.3 billion in insured losses across the metro. We talk through panel thickness and replacement cost before you choose vinyl.
01
What we do:We measure the line, talk through vinyl privacy panels in white or tan, check the permit and HOA rules for the address, and build it. The fence will not need staining or sealing again.
→ A fence that looks the same in year five as it did on install day, with no re-stain cycle.
02
What we do:We check the HOA design rules first — Central Park and similar neighborhoods review material, height, and color before the city permit — then build the approved vinyl spec to the approved height.
→ A fence that passes the HOA review and the city permit without a second round of paperwork.
03
What we do:We measure the side run, confirm the 6-foot rear height rule for the lot, and build a solid vinyl privacy run with a matching gate. Vinyl's clean, uniform face suits a narrow side yard.
→ Full privacy on the side that is overlooked, with a gate that latches cleanly.
04
What we do:We build a low vinyl picket run at or under the 4-foot front limit, with a walk gate that matches. Vinyl holds its color in high-altitude sun without painting.
→ A front fence that frames the yard and needs nothing more than an occasional wash.
Vinyl's pitch is simple: no rot, no stain, no sealing. In Denver that pitch has to survive hail season, high-altitude UV, and freeze-thaw ground. Vinyl handles the UV and the ground line well — it does not absorb water the way wood does — but a hailstone can crack a panel, and a shallow post will heave a rigid panel run out of line faster than it will a wood fence. The material choice is a trade-off, and we would rather talk through it before the build than after the first hailstorm.
Master-planned community on the former Stapleton airport, built mostly 2002 to 2019. The Master Community Association and sub-associations review fence designs before the city permit — two approvals, in that order. On these streets, a low-upkeep vinyl fence is the usual call.
Cherry Creek North is the residential pocket behind the shopping district: early-1900s Craftsman and bungalow streets with small lots of 5,000 to 10,000 square feet and heavy scrape-and-rebuild. A low-upkeep vinyl fence is the usual call on these streets.
A collective hub for North, South, and Northeast Park Hill — three official neighborhoods, not one. The proposed 32-block South Park Hill historic district is proposed, not designated, and Montview Boulevard and 17th Avenue are designated parkways. These streets usually call for a low-upkeep vinyl fence.
One of Denver's oldest neighborhoods, with the Curtis Park Historic District inside it and the Five Points Historic Cultural District designated in 2002. Victorian fronts call for low iron or picket; solid privacy belongs at the rear. On these streets, a low-upkeep vinyl fence is the usual call.
About 4,000 homes built between 1954 and 1957, including 130 to 170 Cliff May prefab ranches — the largest Cliff May tract outside California. Flat, wide lots with detached garages and private courtyards. A low-upkeep vinyl fence is the usual call on these streets.
Hail Alley — the 8 May 2017 storm cost $2.3 billion insured
Denver sits in Hail Alley, with 7 to 9 hail days a year. The 8 May 2017 storm caused $2.3 billion in insured losses across the metro. Vinyl is the most hail-vulnerable fence material; wood and metal fare better. For a vinyl fence, that means choosing a material that survives hail — vinyl is the most vulnerable.
High-altitude UV that weathers wood and vinyl
At 5,280 feet, Denver sun is stronger than at sea level. Unstained cedar turns silver-gray in a few years, and vinyl shows hail and UV wear first on the cheaper panels. On a vinyl fence job, high-altitude sun is part of the material choice, not an afterthought.
Freeze-thaw cycles that heave shallow posts
Denver's freeze-thaw ground lifts shallow posts within a winter or two. Frost depth is commonly cited at about 36 inches in the metro, and posts set shallower than that are the usual cause of a leaning fence. A vinyl fence only holds if the posts are set below the frost line in concrete.
HOA approval comes before the city permit
In master-planned neighborhoods such as Central Park, the association reviews fence material, height, and color before the city zoning permit is filed. The city permit does not satisfy the HOA, and HOA approval does not file a city permit. For a vinyl fence in an HOA neighborhood, the association reviews the material, height, and color first.
Most vinyl calls start with a problem, not a wish list. Here are the four we hear most often, and how we handle each one.
Problem
Vinyl is the most hail-vulnerable fence material in Denver. A big stone cracks a panel, and the crack spreads if the panel is left in place.
Our Fix
We replace the cracked panels individually and check the rails and posts for hidden damage. If several panels failed, we talk through whether the panel spec or the material itself is the right call for an exposed lot.
Problem
A heaved post shows immediately on a rigid vinyl panel run — the panels rack and the rails pull out of the post pockets.
Our Fix
We dig out the failed footing, reset the post deep in fresh concrete, and rehang the panels. If the panel is undamaged, you keep it.
Problem
A vinyl gate without a reinforced frame sags under its own weight, and the latch stops meeting the post.
Our Fix
We diagnose the cause — frame, hinges, or a leaning gate post — and fix the actual problem with a reinforced frame and proper hardware, then test the swing.
Problem
Some HOAs and historic districts restrict vinyl or require a specific color and profile. A fence built to the wrong spec can draw a violation notice.
Our Fix
We review the HOA rules, measure the fence, and work out whether a panel swap, a height adjustment, or a new submittal brings it into compliance.
Vinyl is the low-upkeep option: no staining, no sealing, no rot at the ground line. Here is what you actually get when we build yours — and the trade-offs we will not hide.
No re-stain cycle, ever
Vinyl never needs staining or sealing. It will not rot at the ground line, it will not splinter, and it stays the same color year after year with an occasional wash.
Clean, uniform look
Vinyl panels are identical from post to post, which suits the uniform streetscapes of master-planned neighborhoods and the narrow side yards of central Denver.
Repairable panel by panel
When a hailstone cracks a panel or a branch breaks one, we replace that panel. You do not replace the whole fence for one bad section.
What vinyl fencing costs in the Denver market
Third-party market guides published in October and November 2026 put vinyl privacy fencing at $25 to $75 per linear foot installed. Sources: NumeralQ, 26 Oct 2026; Great Neighbor Fence, 5 Nov 2026; HomeServicesPros, Nov 2026. Those are market ranges, not Payless Fence Company prices. Call (720) 697-2456 with your fence length and material and we will talk through a quote for your yard.
Google ★★★★★4.9 out of 5
Rated 4.9 out of 5 from 27 Google reviews. Read the reviews on our Google Business Profile, or call (720) 697-2456 to talk about your fence.
Vinyl in Denver has to survive hail, high-altitude sun, and freeze-thaw ground. We build it for those conditions: deep concrete footings, reinforced rails and gates, and panels chosen with hail in mind. If your HOA or historic district restricts vinyl, we will tell you before you spend anything — the material check comes before the build, not after.
Payless Fence Company is rated 4.9 out of 5 from 27 Google reviews. The aggregate covers all of our Denver fence work, vinyl included. Call (720) 697-2456 to talk about your vinyl fence.
★★★★★
4.9 out of 5
Based on 27 Google reviews for Payless Fence Company. We do not publish customer quotes on this page; read the reviews on Google, then call us to talk about your fence.
Call (720) 697-2456Real answers to the questions we hear most often on vinyl fence jobs, from local homeowners and property managers.
Cedar and pressure-treated pine fences built for Denver clay, frost, and hail. Pairs with a low-upkeep vinyl run on the same lot.
View Wood Fence InstallationFull-height 6-foot privacy runs for backyards, alleys, and patios. Often built on the same lot as a vinyl fence.
View Privacy Fence InstallationLow wood and vinyl picket fences for front yards and garden edges. A common companion to a vinyl fence.
View Picket Fence InstallationPool fencing checked against the rules, with self-closing, self-latching gates. Pairs with a low-upkeep vinyl run on the same lot.
View Pool Fence InstallationPost, rail, picket, and gate repairs, including storm and freeze-thaw damage. Often built on the same lot as a vinyl fence.
View Fence RepairWood-look composite boards that skip the re-stain cycle. A common companion to a vinyl fence.
View Composite Fence InstallationCall (720) 697-2456 to talk about a vinyl fence. We answer Monday through Sunday, 7:00 AM to 8:00 PM. Have your approximate fence length, the style you are considering, and your neighborhood ready, and we can talk through the next steps on the call.
Phone
(720) 697-2456Address
Payless Fence Company LLC, Denver, CO 80201, US
Hours
Mon–Sun 7:00 AM–8:00 PM
